About:

 

Hope everyone has had a great summer leading up to Apples new MacOS 10.12. Today we have released the Clover USB installation script. The following is the plan for the weekend:

  1. Complete Legacy Clover Guide.
  2. Clean up guides as needed for MacOS 10.12.
  3. Update Clover Screen Shots on the guides as well as the DMG.
  4. Complete upgrade guide using Clover.

Now I will be working on this from 9:00 AM EST to 1:00 PM EST this Saturday. If anyone would wish to help and or inform us of issues with our guides please Skype us and join the group found here.

28 Comments on "Installation and MacOS 10.12 Road Map"

  1. Thanks for the update – keep up the great work!

    Reply
  2. Is it worth upgrading to Sierra right now, with an x79 system? Are there stability improvements over El Cap?

    Reply
  3. Thanks for your work, when will you release the guide ?

    Reply
  4. I already have installed sierra i mean when will your release DSDT and SSDT for Skylake ? will you ever release a Skylake DMG ?

    Reply
  5. I’m having no luck getting audio to work in Sierra. Worked fine in ElCap. ALC1150 GAZ97X-UD3H mobo.

    Tried all methods – toledo, multibeast, audio_cloverALC-120_v1.0b, AppleALC.kext, Apple HDA Patcher.app…

    Anyone have any luck?

    Reply
  6. Hey Guys,

    The Sierra Installer keeps hanging on a circle with a strike-through when I try to boot to it. I’m attempting to update from Mavericks on a GA-X79-UP4 with a 3930k and GTX770.

    I’ve tried booting with: -v cpus=1 npci=0x2000 but it doesn’t seem to help. It gets stuck on a “USB Host Controller” attempt.

    Any ideas?

    Thanks!

    Reply
  7. 10.12 perfectly working with my X79-UP4 except for the usb 3.0.
    Any idea for fix the problem?
    Thanks in advance

    Reply
  8. Is overclocking my 3930K in El Cap/Sierra using the same old method still ok? I haven’t tried it yet.

    Reply
  9. Hi Andrew. Amazing work! Followed instructions for z97x-ud5h. When I use supplied config.plist in dmg, PC will not shut down (restarts). When I boot from install USB, and then launch macOS, PC shuts down (perfectly!). Tried copying config from usb efi to ssd efi, but macOS won’t load. Any ideas how to fix? Everything else works great!

    Reply
  10. Hello? Ready to go.

    Reply
  11. Hello. I am having some trouble with bootup. Most attempts don’t actually boot properly, but I’d say after 3-4 attempts It will fully boot. I have no idea what the problem may be? I did an upgrade from 10.11 and did the normal post install procedure with the latest dmg.

    Any clue what I’m doing wrong or what I am missing?

    4830k
    Gigabyte x79-up4
    nvidia gtx 780

    Reply
  12. Just updated via App Store from 10.12.1 to 10.12.2
    Everything works on my GA-X79-UP4 (except for the usb 3.0).
    For the Nvidia graphics cards:
    After the update, boot with nv_disable=1 and re-run the AGDPfix for full screen resolution.

    Reply
  13. Hey Federico,
    Thanks for your response. My comment was specifically in reference to upgrading from 10.11.6 to 10.12.1.
    I managed to upgrade once I put the kext files in the 10.12 folder on my EFI partition.
    After that I was having trouble getting my graphics to work even with the boot flag: nvda_drv=1 so I used clover configurator to edit my plist and inject Nvidia graphics.

    Reply
    • Sorry Mark. I did a fresh 10.12 installation and then upgrade first 10.12.1 and finally 10.12.2.
      For my Nvidia Geforce 650Ti i ran the AGDPfix to fix the screen resolution

      Reply
  14. Just updated via App Store from 10.12.2 to 10.12.3
    Everything works on my GA-X79-UP4 (also usb 3.0).
    For the Nvidia graphics cards owners:
    After the update, boot with nv_disable=1 and re-run the AGDPfix for full screen resolution.

    Reply

Leave a Reply

Your email address will not be published. Required fields are marked *

Time limit is exhausted. Please reload the CAPTCHA.

About Andrew Kern